Home Off Grid Kit 48V with 8kW Inverter 6.4kW Panels 14.34kW Batteries 5.76kW MPPT

Delivery times 15 days from the order

Home Off Grid Kit 48V with 8kW Inverter, 6.4kW Panels, 14.34kW Batteries and 5.76kW SmartSolar MPPT

Solar Kit consist of 16 400W monocrystalline silicon photovoltaic panels, Victron Energy Quattro 48/8000/110-100 Inverter/Charger, Victron SmartSolar MPPT RS 450/100-Tr 48V 5.76kW Isolated charge controller and 4 Ultimatron 12.8V 280Ah LiFePO4 Lithium Battery with BMS Smart Bluetooth. These components are perfect for having an off-grid photovoltaic system, also called off grid, making a home totally independent from the electricity manager.
The kit contains:
- n°16 400W monocrystalline silicon photovoltaic panels #N52330050286;
- n°1 Victron Energy Quattro 48/8000/110-100 Inverter/Charger #UF69456K;
- n°1 Victron SmartSolar MPPT RS 450/100-Tr 48V 5.76kW Isolated charge controller #UF23617Z;
- n°4 Ultimatron 12.8V 280Ah LiFePO4 Lithium Battery with BMS Smart Bluetooth #ULULM12280.

n°16 Monocrystalline 400W photovoltaic solar panels
Redefined the high-efficiency module series by integrating 182 mm silicon wafers with multi-busbar and half-cut cell technologies. The half-cut cells with additional multibusbar technology increase the efficiency of the cell. In this way they achieve another 2 - 2.5% more performance and can therefore offer maximum reliability. The appealing full black design completes the solar module. Solar modules are certified for use under wind and snow loads of 2400-5400 Pa. The module has a 3.2mm thick, hardened front glass with high light transmission. The frame is anodized aluminum alloy.
• 1500V Higher system voltages can effectively reduce BOS
• Lower operating temperature and temperature perature coefficient,obtain higher profit
• Significantly reduce the effect of hot spot temperature and shadow shielding
• Half-cut design for better mechanical load performance
• Ease of use in more demanding environments
Multi-busbar technology
Busbars are located on each PV module. These are the busbars that are permanently printed on each power cell. They absorb the direct current generated and direct it to the busbars. By using more busbars, Longi has reduced shading, shortened transmission paths and lowered resistance in the modules.
ELECTRICAL PARAMETERS
Max. Power Output Pmax: 400 Wp;
Power Tolerance: 0~+3 %;
Max. Power Voltage Vmp: 30,42 V;
Max. Power Current Imp: 13,15 A;
Open Circuit Voltage Voc: 36,98 V;
Short Circuit Current lsc: 13,78 A;
Module Efficiency: 20,48%
ELECTRICAL PARAMETERS
Max. Power Output Pmax: 298 W;
Max. Power Voltage Vmp: 28,42 V;
Max. Power Current Imp: 10,47 A;
Open Circuit Voltage Voc: 34,9 V;
Short Circuit Current lsc: 11,13 A
TEMPERATURE COEFFICIENT
Temperature Coefficients of Pmax: -0,32%/°C;
Temperature Coefficients of Voc: -0,26%/°C;
Temperature Coefficients of lsc: +0,054%/°C
MECHANICAL PARAMETERS
Cell Type: Mono 182x91 mm;
Number of Cells: 108 pcs (2x(6x9));
Dimensions ( L*W*H ): 1722x1134x35 mm;
Weight: 22 kg;
Frame: Anodized Aluminum;
Junction Box: IP68;
Cable, Length: 4 mmq/350 mm
OPERATING CONDITION
Maximum System Voltage: 1500 V (DC);
Operating Temperature: -40~+85;
Max. Wind Load / Snow Load: 2400/5400;
Max. Over Current: 25A;
Application Class: Class A;
Fire Rating: Class C;
NMOT: 42±3 °C.

n°1 Victron Energy Quattro 48/8000/110-100 Inverter 48V 8kW Battery Charger 110A
Similar to the MultiPlus, the Quattro is also a combined inverter and charger. Additionally it can accept two AC inputs and automatically connect to the active source. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology plus multiple system integration features such as three or split phase operation and parallel operation.
Two AC Inputs & two AC Outputs
The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output.
Unique PowerAssist feature
The Quattro will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery.
Virtually unlimited power thanks to parallel operation
Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities.
Remote Monitoring and Control
When coupled with a GX device (e.g. Cerbo GX) you can monitor and control your Quattro and system or systems' locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, from adjusting your Quattro to auto starting a backupgenerator and more…
Specifications:
PowerControl & PowerAssist: Yes
Integrated Transfer switch: Yes
Input voltage range: 187-265VAC
Input frequency: 45–65Hz with Power factor: 1
Maximum feed through current (A): 2x 100
Weight: 41 kg
Dimensions (HxWxD): 470x350x280 mm
INVERTER
Input voltage range: 38-66V
Output voltage: 230 VAC ± 2%
Frequency: 50 Hz ± 0,1%
Cont. output power at 25°C: 8000 VA
Cont. output power at 25°C: 6400 W
Cont. output power at 40°C: 5500 W
Cont. output power at 65°C: 3600 W
Peak power: 16000 W
Maximum efficiency: 96%
Zero load power: 60 W
Zero load power in AES mode: 40 W
Zero load power in Search mode: 15 W
CHARGER
Charge voltage 'absorption': 57.6V DC
Charge voltage 'float': 55.2V DC
Storage mode: 52.8V DC
Charge current house battery: 110 A
Battery temperature sensor: Yes

n°1 Victron SmartSolar MPPT RS 450/100-Tr 48V 5.76kW Isolated charge controller
The SmartSolar MPPT RS 48V 5.76kW solar charge controller is Victron's solution for systems with large series connected PV arrays charging 48V DC battery banks. This product is perfect for large off-grid, and grid connected battery systems.
Features include a wide 80-450 VDC operating solar voltage input, independent tracking inputs, full connectivity, isolated PV connections, display screen, fully programmable battery charging parameters and active cooling. The new metal case design and fully covered electrical connections improve the safety and modernise the presentation in line with the latest suite of Victron products.
MPPT: Ultra Fast Maximum Power Point Tracking
The SmartSolar RS solar charge controller connects to a PV array of between 80 and 450 Volt Voc and will efficiently charge your 48V battery bank with either 100A.
The charge settings are fully programmable and can be set up for different battery chemistries, like lead-acid, lithium and more.
Setup and monitor with VictronConnect
The SmartSolar RS charge controller can be remotely controlled and configured over Bluetooth via the VictronConnect App. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, historical data and trends.
Daisy Chain Additional Units
The SmartSolar RS charge controller is equipped with VE.Can bus ports. This allows for communication with additional SmartSolar RS & VE.Can MPPT units. The additional units are simply “daisy chained” to each other with an RJ45 cable.
When connected to each other, all individual charge controllers, will synchronise their charge stages. They can also send their data, via the same cable, for monitoring to a GX device (such as the Cerbo GX).
Remote Monitoring and Control
If the GX device is connected to the internet, the Victron Remote Management Portal (VRM) provides access to the full power of your SmartSolar RS charge controllers.
If your installation is connected to a GX device and the internet, Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; for free.
For remote installations - even when there is no internet connection nearby - you may be able to monitor your MPPT by connecting the  GlobalLink 520.
SmartSolar Display
The SmartSolar RS charge controller is equipped with a display on the front panel. The display reads battery volts, charge current and voltages from both array’s individually including instantaneous and total figures and unit status including any possible error codes.
I/O Connections
The SmartSolar RS charge controller is equipped with a programmable relay and options for remote temperature and voltage sensing. The remote input can accept the Victron smallBMS and other types of BMS with allow-to-charge signals. 
Specifiche tecniche
Isolated MPPT SmartSolar RS: 450/100
Battery Voltage: 48V
Rated Charging Current: 100A
Maximum charge power: 5.8 kW at 57.6 V
"Absorption" charge voltage: Default: 57.6V (adjustable)
Trickle charge voltage: Default: 55.2V (adjustable)
Programmable voltage range: Minimum: 36V | Maximum: 60V (7)
Charging algorithm: Multi-step adaptive (adjustable)
Battery temperature sensor: Included
Maximum efficiency: 96%
Self-consumption: 15mA
SOLAR
PV Maximum DC Voltage: 450V
Starting Voltage: 120V
MPPT operating voltage range: 80 – 450V (1)
Number of plotters: 2
Maximum PV operating input current: 18A per tracker
PV short circuit current: 20A per tracker
Maximum output DC charging power: 4000W per tracker 5760W total
Maximum PV module size per tracker: 7200 Wp (450 V x 20 A)
PV insulation fault level: 100 kΩ
GENERAL
Synchronized parallel operation: Yes, up to 25 units with VE.Can
Programmable Relay: Yes
Protection: PV reverse polarity, Output short circuit, Over temperature
Data communication: VE.Direct port, VE.Can port and Bluetooth (6)
Bluetooth Frequency: 2402-2480MHz
Bluetooth power: 4dBm
General purpose analog/digital input port: Yes, 2x
Remote on-off: Yes
Operating temperature range: -40 to +60 °C (fan cooled)
Humidity (non-condensing): max 95%
CARCASS
Material and colour: steel, blue RAL 5012
Protection category: IP21
Battery connection: M8 bolts
PV input power terminals: 2.5…16 mm2
Weight: 7.9 kg
Size: 440x313x126 mm
REGULATIONS
Safety: EN-IEC 62109-1, EN-IEC 62109-2
Country of Origin: Designed in the Netherlands, made in India

n°4 Ultimatron 12.8V 280Ah LiFePO4 Lithium Battery with BMS Smart Bluetooth
LiFePO4 lithium battery is definitely the best alternative to 12V lead batteries because they have a stable supply voltage even under heavy load. Offering the advantages of lithium: light weight, stable voltage, high number of cycles. It can directly store more than 96% of the energy supplied. High performance even in extreme conditions. Deep and constant discharge and refill efficiency.
Furthermore, thanks to the BMS (Battery Management System) Smart integrated with Bluetooth 4.0 connection, it is possible to monitor the values in real time and the status of the battery directly from your smartphone thanks to the convenient dedicated App, for smartphone or tablet.
The fields of application of lithium batteries are diverse, especially for stationary or mobile use. In particular, mobile homes, solar boats, electric boats, electric scooters, golf cars or even electromobiles / wheelchairs and cleaning machines are increasingly equipped.
Series and parallel connection for 12V, 24V applications.
Electrical performance
Nominal voltage: 12.8V
Nominal capacity: 280Ah
Capacity @ 120A: 300 min
Energy: 3584Wh
Resistance: ≤15mΩ @ 50% SOC
Self discharge: <3% / Month
Cells: LiFePO4 Cells
Discharge performance
Continuous discharge current: 50A
Maximum continuous discharge current: 200A
Peak discharge Cut-Off current: 400A/1s
Recommended low voltage disconnect: 10V
Discharge Cut-Off voltage: >9.6V (50 ~ 150ms)
Reconnect voltage: >10V
Short circuit protection: 200~600μs
Charge performance
Recommended charge current: 100A
Maximum charge current: 200A
Recommended charge voltage: 14.6V
Charge Cut-Off voltage: <15.2V (0.5 ~ 1.5s)
Reconnect voltage: >14.4V
Balancing voltage: <14V
Performance in temperature
Discharge temperature: -20 ~ 60 °C
Charge temperature: 0 ~ 45 °C
Storage temperature: -5 ~ 35 °C
High temperature Cut-Off: 65 °C
Reconnect temperature: 48 °C
Mechanical performance
Terminal type: M8
Terminal torque: 80 ~ 100 in-lbs (9 ~ 11 N-m)
Bluetooth: Bluetooth 4.0 with smartphone app
Case material: metal
Enclosure protection: IP65
Extension: LED display
Dimension (LxWxH): 355x330x190 mm
Weight: 31 kg
Compliance
Shipping classification: UN 3480, CLASS 9
Certifications: CE, UN38.3, UL1642 & IEC62133

IMPORTANT NOTE:
The reduced VAT is reserved for PRIVATE INDIVIDUALS, end users and qualified photovoltaic and thermal energy installers or heat production INSTALLED IN ITALY. In case you do not have the right to the tax deduction (DEALERS) kindly contact us in advance so that an invoice with 22% VAT can be issued as per the law in force. In the absence of receipt of the declaration the order cannot be shipped as a copy of the VAT declaration form must by law be attached to the company invoice. The declaration form and ID document must be sent to the email address. 
After purchase, kindly complete and return the VAT declaration form together with a copy of an ID document.

For more details, we recommend viewing the technical data sheets of each single component of the kit or asking our technicians for information.