48V 4.8kW Photovoltaic Kit with 5.6kW Inverter & LiFePo4 2x5kW Batteries

Delivery times 15 days from the order

48V 4.8kW Photovoltaic Kit with 5.6kW Off Grid Solar Inverter

Solar Kit consist of 12 400W monocrystalline silicon photovoltaic panels, TopSolar VM IV 5600VA 5.6kW 230V Off Grid Solar Inverter 48V MPPT, 2 LiFePo4 4.8kWh 48V Pylontech lithium batteries and kid cables for Off-Grid systems with grid support.
For more details, we recommend viewing the technical data sheets of each single component of the kit or asking our technicians for information.
The kit contains:
- n°12 400W monocrystalline silicon photovoltaic panels #N52330050286;
- n°1 TopSolar VM IV 5600VA 5.6kW 230V #N52722022030;
- n°2 Pylontech US5000C LiFePo4 4.8kWh 48V Lithium battery #OF013800;
- n°1 Cable Kit #OF012800.

Set of 12 Monocrystalline 400W photovoltaic solar panels
Redefined the high-efficiency module series by integrating 182 mm silicon wafers with multi-busbar and half-cut cell technologies. The half-cut cells with additional multibusbar technology increase the efficiency of the cell. In this way they achieve another 2 - 2.5% more performance and can therefore offer maximum reliability. The appealing full black design completes the solar module. Solar modules are certified for use under wind and snow loads of 2400-5400 Pa. The module has a 3.2mm thick, hardened front glass with high light transmission. The frame is anodized aluminum alloy.
• 1500V Higher system voltages can effectively reduce BOS
• Lower operating temperature and temperature perature coefficient,obtain higher profit
• Significantly reduce the effect of hot spot temperature and shadow shielding
• Half-cut design for better mechanical load performance
• Ease of use in more demanding environments
Multi-busbar technology
Busbars are located on each PV module. These are the busbars that are permanently printed on each power cell. They absorb the direct current generated and direct it to the busbars. By using more busbars, Longi has reduced shading, shortened transmission paths and lowered resistance in the modules.

ELECTRICAL PARAMETERS
Max. Power Output Pmax: 400 Wp;
Power Tolerance: 0~+3 %;
Max. Power Voltage Vmp: 30,42 V;
Max. Power Current Imp: 13,15 A;
Open Circuit Voltage Voc: 36,98 V;
Short Circuit Current lsc: 13,78 A;
Module Efficiency: 20,48%
ELECTRICAL PARAMETERS
Max. Power Output Pmax: 298 W;
Max. Power Voltage Vmp: 28,42 V;
Max. Power Current Imp: 10,47 A;
Open Circuit Voltage Voc: 34,9 V;
Short Circuit Current lsc: 11,13 A
TEMPERATURE COEFFICIENT
Temperature Coefficients of Pmax: -0,32%/°C;
Temperature Coefficients of Voc: -0,26%/°C;
Temperature Coefficients of lsc: +0,054%/°C
MECHANICAL PARAMETERS
Cell Type: Mono 182x91 mm;
Number of Cells: 108 pcs (2x(6x9));
Dimensions ( L*W*H ): 1722x1134x35 mm;
Weight: 22 kg;
Frame: Anodized Aluminum;
Junction Box: IP68;
Cable, Length: 4 mmq/350 mm
OPERATING CONDITION
Maximum System Voltage: 1500 V (DC);
Operating Temperature: -40~+85;
Max. Wind Load / Snow Load: 2400/5400;
Max. Over Current: 25A;
Application Class: Class A;
Fire Rating: Class C;
NMOT: 42±3 °C.

TopSolar VM IV 5600VA 5.6kW 230V Off Grid Solar Inverter 48V MPPT
Ideal for stand-alone or hybrid photovoltaic systems with mains or generator AC input. This inverter with display enables the realization of an OFF GRID photovoltaic system of up to 5.6kW to recharge a 48V battery bank and the use of 230V alternate current with 230V AC supplementary input for emergency generator or grid supplier. The ALL in ONE inverter is the simplest way to realize a stand alone PV system with automatic switch with the grid (or emergency generator), all the components that usually make up a classic stand alone photovoltaic system (charge controller, inverter, emergency unit and battery chargers). With this inverter you may use renewable sources, hence solar energy, battery stored energy and only in the absence of these two renewable sources, the inverter automatically switches to emergency AC input of the generator or grid supplier. This system allows maximum cost saving in your electricity bill or even eliminating the connection to the grid.
• Pure sinewave inverter.
• Support Bluetooth for mobile (Android App available).
• Detachable LCD control module with multiple communications.
• High efficiency pure sine wave inverter (PF=1).
• Wide PV input range (120 V DC - 500V DC) 80A MPPT SCC.
• Intelligent 3 stage 60A AC battery charger to optimize battery performance.
• Surger to 2X continuos power for 5 seconds fir motor loads.
• Built-in MPPT solar charge controller .
• Selectable input voltage range depending on the applications.
• Configurable AC/Solar input priority via LCD setting.
• Automatic start in the absence of AC current.

INVERTER OUTPUT:
- Rated Power: 5600VA/5600W;
- Surge Power: 11200VA;
- Waveform: Pure sine wave;
- AC Voltage Regulation (Batt.Mode): 230VAC±5%;
- Inverter Efficiency (Peak): 90-93%;
- Transfer Time: 15ms (For Personal Computers) 20ms(For Home Appliances).
AC INPUT:
- Voltage: 230VAC;
- Selectable Voltage Range: 170~280VAC (For Personal Computers) 90~280VAC (For Home Appliances);
- Frequency Range: 50Hz/60Hz (Auto sensing).
BATTERY:
- Nominal voltage: 48 VDC;
- Floating Charge Voltage: 54 VDC;
- Overcharge Protection: 63 VDC.
SOLAR CHARGER & AC CHARGER:
- Solar charger type: MPPT;
- Maximum PV Array Power: 6000W;
- MPPT Range @ Operating Voltage: 120~450 VDC;
- Maximum PV Array Open Circuit Voltage: 500 VDC;
- Maximum Solar Charge Current: 120A;
- Maximum AC Charge Current: 100A;
- Maximum Charge Current: 120A;
- Maximum Efficiency: 98%.
MECHANICAL SPECIFICATION
- Model Number: VM IV 5600;
- Dimension, WxHxD: 430x338x126 mm;
- Net Weight: 13 kg.
- Humidity: 5% to 95% Relative Humidity (Non-condensing);
- Operating Temperature: 10 °C - 50 °C;
- Storage Temperature: -15 °C - 60 °C.

• Pylontech US5000C LiFePo4 4.8kWh 48V Lithium battery

The us5000c is a lithium storage system of the latest generation. The accumulator was specially developed to fully meet the high demands placed on a solar accumulator today. Maximum safety and a long service life are guaranteed even with regular deep discharge thanks to the latest technology.
The latest battery of the market-leading manufacturer with now 4.8kWh per module has again a battery management system (bms) built into each module and therefore offers a lot of security. Internally, the individual cells are thus monitored and balanced against overvoltage, overtemperature, deep discharge, etc. protected. The battery is compatible and certified with many available inverters.
Features
•    Extremely cycle resistant - over 6000 cycles at 95% DoD
•    More usable energy content than the previous model US5000
•    Lifetime over 10 years
•    Absolutely intrinsically safe lithium technology
•    Compatible with many available inverters
•    Automatic address setting when connected in multi-groups
•    High charging and discharging power possible
•    Integrated BMS
•    Very high storage density - low weight and compact design
•    Easy installation thanks to modular design
•    Absolutely maintenance-free and durable
•    Built-in soft-start function capable of reducing the current surge when the inverter is started from the battery
•    Dual active protection at BMS level
•    Supports WakeUp by 5-12V signal from rj45 port
•    Pre-charge function to protect ESS system from overvoltage function
Battery management system in each module
The battery management system integrated in each module protects each installed battery cell from harmful influences over the entire life of the module and effectively prevents premature failure.
Protection against:
•    Deep discharge and overcharge
•    overvoltage during charging
•    excessive currents during charging and discharging
•    over and under temperature
•    Short circuit and reverse polarity
Constant monitoring of the individual cell voltages (cell balance)
Modular design
The system has a modular design and can be configured precisely to the desired storage capacity by interconnecting several modules. Each storage module consists of a high-performance lithium iron phosphate (LiFePo4) accumulator and an integrated BMS.
High cycle life
The extremely high cycle life of the installed LiFePo4 cells make Pylontech us3000c modules the optimal storage solution for photovoltaic systems. Regardless of whether the solar system is grid-connected or stand-alone, the Pylontech storage system offers several advantages over typical lead-acid batteries and other lithium technologies.

Technical data
-    Battery Type: Lithium Iron Phosphate (LiFePo4);
-    Rated voltage: 48V;
-    Rated capacity: 4800 Wh;
-    Usable capacity (95% DoD): 4560 Wh;
-    Discharge voltage range: 44.5 - 53.5V;
-    Charging voltage range: 52.5 - 53.5V;
-    Max. Peak (discharge) charging current: 200A @15sec;
-    Max. (Discharge) charging current: 120A @15min;
-    Recommended charge/discharge current: 75A;
-    Communication: rs485, CAN;
-    Protection class: IP20;
-    Temperature range charge: 0°C - +50°C;
-    Temperature range discharge: -10°C - +50°C;
-    Temperature range storage: -20°C - +60°C;
-    Service life: over 10 years;
-    Cycle life: over 6000 at 95% DoD;
-    BMS / monitoring: integrated in each module;
-    Dimensions: 442x420x161 mm;
-    Weight: 38 kg;
-    Warranty: 10 years manufacturer warranty;
-    Certification: TÜV, ce, UN38.8.

• Cable set to connect the batteries of Pylontech with an inverter
The Pylontech battery connection cable set includes 2 x 2 meter cables (plus/minus) with a cross section of 25mm² each and a CAN data cable with rj45 connectors on both sides. The set is needed to connect the batteries of Pylontech with an inverter.
Content
-    2m cable plus with m8 ring cable lug and amphenol connector (Pylontech).
-    2m cable minus with m8 ring cable lug and Amphenol connector (Pylontech).
-    CAN data cable with rj45 connectors on both ends.

IMPORTANT NOTE:
The reduced VAT is reserved for PRIVATE INDIVIDUALS, end users and qualified photovoltaic and thermal energy installers or heat production INSTALLED IN ITALY. In case you do not have the right to the tax deduction (DEALERS) kindly contact us in advance so that an invoice with 22% VAT can be issued as per the law in force. In the absence of receipt of the declaration the order cannot be shipped as a copy of the VAT declaration form must by law be attached to the company invoice. The declaration form and ID document must be sent to the email address. 
After purchase, kindly complete and return the VAT declaration form together with a copy of an ID document.